Nordic nRF53

The nRF53 series of chips from Nordic Semiconductor are based around an two ARM Cortex-M33 cores and a multiprotocol 2.4 GHz transceiver.

Peripheral Support

The following list indicates peripherals supported in NuttX:

Peripheral

Support

Notes

GPIO

Yes

GPIOTE

Yes

I2S

No

MWU

No

NFCT

No

PDM

No

DPPI

No

PWM

Yes

QDEC

No

QSPI

Yes

RADIO

No

RNG

No

RTC

Yes

SAADC

Yes

SPIM

Yes

SPIS

No

TEMP

No

TIMER

Yes

TWIM

Yes

TWIS

No

UART

Yes

UARTE

No

USBD

Yes

WDT

No

IPC

Yes

RPTUN supported

GPIO/GPIOTE

Pins can be configured/operated using nrf53_gpio_* functions. Interrupts are handled via the GPIOTE peripheral in one of two ways: via a GPIOTE channel or via PORT events. The former allows for simultaneous rising/falling edge-sensitive interrupts per-pin. However, as there are a limited number of channels (and sometimes these are used by some drivers for specific tasks), it may not always be possible to use this mechanism. The latter approach for pin interrupts is via the PORT event, determined by pin state on a their corresponding GPIO port. This is related to the SENSE capability of pins, which can only be set to either rising or falling edge sensing.

Depending on CONFIG_NRF53_PER_PIN_INTERRUPTS option, you can set a callback for the PORT event itself or you can set a callback for a given pin. In the latter case the driver scans for pins with DETECT bit high and calls the configured callback automatically.

Finally, GPIOTE can also be used to configure a channel in task mode, which allows to control pin state via tasks/events.

ADC

The SAADC peripheral is exposed via standard ADC driver. The lower-half of this driver is initialized by calling nrf53_adcinitialize().

I2C

I2C is supported both in polling and interrupt mode (via EasyDMA).

Note

The I2C peripheral does not support sending two transfers without sending a START nor RSTART. For this reason, this is supported via an internal buffer where messages will be first copied to and sent together.

The lower-half of I2C bus is initialized by nrf53_i2cbus_initialize().

SPI

SPI is supported both in polling and interrupt-based (via EasyDMA) mode. The latter supports arbitrarily long transfers using Nordic’s list-mode EasyDMA (intermediate transfers are currently still manually started).

It is possible to use SPI without either MOSI/MISO pin defined by simply not providing the relevant BOARD_SPI*_MISO/MOSI_PIN definition.

This implementation support power management hooks, which will disable SPI peripheral when entering either SLEEP or STANDBY modes and reconfigure it when going back to NORMAL mode.

UART

UART is implemented using polling. UARTE EasyDMA feature is not yet supported. This may introduce a large number of interrupts which may be undesirable.

PWM

PWM is supported via standard driver. This means that more advanced features such as complex sequences or waveform modes are not yet supported.

QSPI

QSPI is supported both in interrupt-based (via EasyDMA) mode and is exposed via standard QSPI interface.

TIMER

The TIMER peripheral is exposed as standard timer.

RTC

The RTC peripheral is exposed as a standard timer, since it is really a low-power timer, without any date handling capabilities.

USBD

The USBD peripheral is exposed via standard USBDEV interface.

Interprocessor Communication

Interprocessor communication between the application core and the network core is realized with the NuttX RPTUN device based on the OpenAMP framework.

The last 32kB of the application core RAM is used for a shared memory (address = 0x20078000).

BLE Support

BLE is supported in the nRF53 using Nordic’s SoftDevice Controller.

Tool Issues

OpenOCD

There is no official support for Nordic Cortex M33 chips (nRF9160 or nRF5340).

Flashing locked device

  1. Unlock the network core:

    nrfjprog --recover --coprocessor CP_NETWORK
    
  2. Unlock the application core:

    nrfjprog --recover
    
  3. Flash the network core:

    nrfjprog --coprocessor CP_NETWORK --program nuttx_net.hex --verify --chiperase
    
  4. Flash the application core:

    nrfjprog --program nuttx_app.hex --verify --chiperase
    

Supported Boards