ESP32-AUDIO-KIT

The Ai-Thinker ESP32 Audio Kit is a development board for the ESP32 SoC from Espressif, based on Ai-Thinker ESP32-A1S audio module.

../../../../../_images/esp32-audio-kit.png

Ai-Thinker ESP32 Audio Kit board

Features

  • ESP32-A1S module

  • Audio Earphones Output

  • Audio LINEIN Input

  • 2 Microphones in the board (stereo audio input)

  • 8 Buttons in the boards (1 RST Button and 7 user buttons)

  • MicroSD card slot

Some of the ESP32 I/O pins are broken out to the board’s pin header.

Serial Console

UART0 is, by default, the serial console. It connects to the on-board Silabs CP2102 converter and is available on the USB connector (UART label).

It will show up as /dev/ttyUSB[n] where [n] normally is 0 if you don’t have another USB/Serial adapter connected in your computer.

Buttons and LEDs

Board Buttons

There are eight buttons labeled as RST, BOOT, KEY1..KEY6. The RST button is not available to software.

The BOOT button is connected to IO0. On reset it is used as a strapping pin to determine whether the chip boots normally or into the serial bootloader. After reset, however, the BOOT button can be used for software input.

Board LEDs

There are several on-board LEDs for that indicate the presence of power and USB activity.

I/O Mapping

I/O

Signal

Notes

0

BOOT Button

2

DATA0 SDCard

4

DATA1 SDCard

5

KEY6 Button

12

DATA2 SDCard

13

KEY2 Button/DATA3 SDCard

(DIP Switch)

14

CLK SDCard

15

CMD SDCard/JTAG MTDO

(DIP Switch)

18

KEY5 Button

19

KEY3 Button/LED5

21

CTRL Audio AMP

22

LED4

23

KEY4 Button

34

SDCard Detect

36

KEY1 Button

Configurations

All of the configurations presented below can be tested by running the following commands:

$ ./tools/configure.sh esp32-audio-kit:<config_name>
$ make flash ESPTOOL_PORT=/dev/ttyUSB0 -j

Where <config_name> is the name of board configuration you want to use, i.e.: nsh, buttons, wifi… Then use a serial console terminal like minicom or picocom configured to 115200 8N1.

audio

This configuration uses the I2S0 peripheral and the ES8388 audio codec present on the ESP32-Audio-Kit board to play an audio file streamed over HTTP while connected to a Wi-Fi network.

Simple HTTP server

Prepare a PCM-encoded (.wav) audio file with 16 bits/sample (sampled at 44.1kHz). This file must be placed into a folder in a computer that could be accessed on the same Wi-Fi network the ESP32 will be connecting to.

Python provides a simple HTTP server. cd to the audio file folder on the PC and run:

$ python3 -m http.server

Serving HTTP on 0.0.0.0 port 8000 (http://0.0.0.0:8000/)

Look for your PC IP address and test playing the prepared audio on your browser:

../../../../../_images/esp32-audio-config-file1.png

After successfully built and flashed, connect the board to the Wi-Fi network:

$ nsh> wapi psk wlan0 mypasswd 3
$ nsh> wapi essid wlan0 myssid 1
$ nsh> renew wlan0

Once connected, open NuttX’s player and play the file according to its file name and the IP address of the HTTP server (For example tone.wav and 192.168.1.239:8000, respectively):

$ nsh> nxplayer
$ nxplayer> play http://192.168.1.239:8000/tone.wav

Note

The codec implementation on the LyraT board was validated using 16-bit, 44.1kHz WAV files. Other configurations might not work as expected.

nsh

Basic NuttShell configuration (console enabled in UART0, exposed via USB connection by means of FT2232HL converter, at 115200 bps).

wifi

Enables Wi-Fi support. You can define your credentials this way:

$ make menuconfig
-> Application Configuration
    -> Network Utilities
        -> Network initialization (NETUTILS_NETINIT [=y])
            -> WAPI Configuration

Or if you don’t want to keep it saved in the firmware you can do it at runtime:

nsh> wapi psk wlan0 mypasswd 3
nsh> wapi essid wlan0 myssid 1
nsh> renew wlan0

Tip

Please refer to ESP32 Wi-Fi Station Mode for more information.