PINE64 Ox64

Ox64 is a RISC-V Single-Board Computer based on the Bouffalo Lab BL808 RISC-V SoC with C906 64-bit CPU Core and E907 / E902 32-bit CPU Cores supported by 64 MB of embedded PSRAM memory, with built-in WiFi, Bluetooth and Zigbee radio interfaces.

Ox64 comes in a breadboard-friendly form factor. It has a microSD Card slot, USB 2.0 Type-C port and other peripheral interfaces.

Features

  • System on Chip: Bouffalo Lab BL808
    • CPU:

      • 64-bit T-Head C906 “D0” (RV64IMAFCV)

      • 32-bit T-Head E907 “M0” (RV32IMAFCP)

      • 32-bit T-Head E902 “LP” (RV32E[M]C)

    • RAM: Embedded 64 MB PSRAM

  • Wireless: 2.4 GHz 1T1R WiFi 802.11 b/g/n, Bluetooth 5.2, Zigbee

  • Ethernet: 10 / 100 Mbps (optional)

  • Storage: On-board 128 Mbit (16 MB) XSPI NOR Flash Memory, microSD (SDHC and SDXC)

  • USB: USB 2.0 OTG

  • Audio: Microphone and Speaker (optional)

  • Video Input: Dual-lane MIPI CSI port for Camera Module (USB-C)

  • Expansion Ports: 26 GPIO pins (including SPI, I2C and UART)

Serial Console

A USB Serial Adapter that supports 2 Mbps (like CH340G Serial Adapter) is required to run NuttX on Ox64.

Connect the USB Serial Adapter to Ox64 Serial Console at:

USB Serial

Ox64 Pin

TX

Pin 31 (GPIO 17 / UART3 RX)

RX

Pin 32 (GPIO 16 / UART3 TX)

GND

Pin 33 (GND)

On the USB Serial Adapter, set the Voltage Level to 3V3.

Connect Ox64 to our computer with the USB Serial Adapter. On our computer, start a Serial Terminal and connect to the USB Serial Port at 2 Mbps.

NuttX will appear in the Serial Console when it boots on Ox64.

RISC-V Toolchain

Before building NuttX for Ox64, download the RISC-V Toolchain riscv64-unknown-elf from SiFive RISC-V Tools.

Add the downloaded toolchain riscv64-unknown-elf-toolchain-.../bin to the PATH Environment Variable.

Check the RISC-V Toolchain:

$ riscv64-unknown-elf-gcc -v

Building

To build NuttX for Ox64, install the prerequisites and clone the git repositories for nuttx and apps.

Configure the NuttX project and build the project:

$ cd nuttx
$ tools/configure.sh ox64:nsh
$ make
$ riscv64-unknown-elf-objcopy -O binary nuttx nuttx.bin

This produces the NuttX Kernel nuttx.bin. Next, build the NuttX Apps Filesystem:

$ make export
$ pushd ../apps
$ tools/mkimport.sh -z -x ../nuttx/nuttx-export-*.tar.gz
$ make import
$ popd
$ genromfs -f initrd -d ../apps/bin -V "NuttXBootVol"

This generates the Initial RAM Disk initrd.

Package the NuttX Kernel and Initial RAM Disk into a NuttX Image:

$ head -c 65536 /dev/zero >/tmp/nuttx.pad
$ cat nuttx.bin /tmp/nuttx.pad initrd >Image

The NuttX Image Image will be copied to a microSD Card in the next step.

Booting

To boot NuttX on Ox64, flash OpenSBI and U-Boot Bootloader to Ox64.

NuttX boots on Star64 via a microSD Card. Prepare a Linux microSD Card for Ox64.

Copy the file Image from the previous section and overwrite the file on the microSD Card.

Check that Ox64 is connected to our computer via a USB Serial Adapter at 2 Mbps.

Insert the microSD Card into Ox64 and power up Ox64 via the Micro USB Port. NuttX boots on Ox64 and NuttShell (nsh) appears in the Serial Console.

To see the available commands in NuttShell:

$ help

Configurations

nsh

Basic configuration that runs NuttShell (nsh). This configuration is focused on low level, command-line driver testing. Built-in applications are supported, but none are enabled. Serial Console is enabled on UART3 at 2 Mbps.

Peripheral Support

NuttX for Ox64 supports these peripherals:

Peripheral

Support

NOTES

UART

Yes