ESP32-LyraT V4.3

The ESP32-LyraT development board is a hardware platform designed for the dual-core ESP32 audio applications, e.g., Wi-Fi or BT audio speakers, speech-based remote controllers, smart-home appliances with audio functionality(ies), etc. You can find the board schematic here.

ESP32 LyraT V4.3 Board Layout

ESP32-LyraT V4.3 Board Layout

The block diagram below presents main components of the ESP32-LyraT.

ESP32 LyraT V4.3 Electrical Block Diagram

ESP32-LyraT V4.3 Electrical Block Diagram

Features

  • ESP32-WROVER-E Module

  • JTAG Interface

  • MicroSD Slot

  • Audio Codec Chip

  • Battery Charger Chip

  • Touch Pad Buttons

Serial Console

UART0 is, by default, the serial console. It connects to the on-board CP2102N bridge and is available on the USB connector.

It will show up as /dev/ttyUSB[n] where [n] will probably be 0.

Buttons and LEDs

Buttons

Two key labeled Rec and Mode. They are routed to ESP32-WROVER-E Module and intended for developing and testing a UI for audio applications using dedicated API.

Four touch pads labeled Play, Sel, Vol+ and Vol-. They are routed to ESP32-WROVER-E Module and intended for development and testing of a UI for audio applications using dedicated API. They are currently not supported as the driver is in development.

There are two buttons labeled Boot and EN. The EN button pulls the chip enable line that doubles as a reset line. The BOOT button is connected to IO0. On reset it is used as a strapping pin to determine whether the chip boots normally or into the serial bootloader.

Entering of the ESP32 into upload mode may be done in two ways:

  • Manually by pressing both Boot and RST keys and then releasing first RST and then Boot key.

  • Automatically by software performing the upload. The software is using DTR and RTS signals of the serial interface to control states of EN, IO0 and IO2 pins of the ESP32. This functionality is enabled by installing jumpers in three headers JP23, JP24 and JP25. Remove all jumpers after upload is complete.

LEDs

A general purpose green LED controlled by the ESP32-WROVER-E Module to indicate certain operation states of the audio application using dedicated API. It can also be used by the user for other purposes.

The Standby green LED indicates that power has been applied to the Micro USB Port. The Charging red LED indicates that a battery connected to the Battery Socket is being charged.

Audio Codec

This is currently unsupported. Drivers still in development.

The Audio Codec Chip, ES8388, is a low power stereo audio codec with a headphone amplifier. It consists of 2-channel ADC, 2-channel DAC, microphone amplifier, headphone amplifier , digital sound effects, analog mixing and gain functions. It is interfaced with ESP32-WROVER-E Module over I2S and I2S buses to provide audio processing in hardware independently from the audio application.

It also provides:

  • Onboard microphone connected to IN1 of the Audio Codec Chip.

  • Auxiliary input socket connected to IN2 (left and right channel) of the Audio Codec Chip. Use a 3.5 mm stereo jack to connect to this socket.

  • Output socket to connect headphones with a 3.5 mm stereo jack.

Note

The socket may be used with mobile phone headsets and is compatible with OMPT standard headsets only. It does work with CTIA headsets. Please refer to Phone connector (audio) on Wikipedia.

  • Output socket to connect a speaker. The 4-ohm and 3-watt speaker is recommended. The pins have a 2.00 mm / 0.08” pitch.

The development board uses two mono Class D amplifier ICs, model number NS4150 with maximum output power of 3W and operating voltage from 3.0V to 5.25V. The audio input source is the digital-to-analog converter (DAC) output of the ES8388. Audio output supports two external speakers. An optional audio output is a pair of headphones feed from the same DACs as the amplifier ICs.

To switch between using headphones and speakers, the board provides a digital input signal to detect when a headphone jack is inserted and a digital output signal to enable or disable the amplifier ICs. In other words selection between speakers and headphones is under software control instead of using mechanical contacts that would disconnect speakers once a headphone jack is inserted.

Note

The codec implementation on the LyraT board was validated using 16-bit, 44.1kHz WAV files. Other configurations might not work as expected.

SD card

The development board supports a MicroSD card in SPI/1-bit/4-bit modes, and can store or play audio files in the MicroSD card. Note that JTAG cannot be used and should be disconnected by setting Function DIP Switch when MicroSD Card is in operation, because some of signals are shared by both devices.

Enable MicroSD Card in 1-wire Mode

Set Function DIP Switch to:

DIP SW

Position

1

OFF

2

OFF

3

OFF

4

OFF

5

OFF

6

OFF

7

OFF 1

8

n/a

  1. AUX Input detection may be enabled by toggling the DIP SW 7 ON. Note that the AUX Input signal pin should not be be plugged in when the system powers up. Otherwise the ESP32 may not be able to boot correctly.

In this mode:

  • JTAG functionality is not available

  • Vol- touch button is available for use with the API

Enable MicroSD Card in 4-wire Mode

Set Function DIP Switch to:

DIP SW

Position

1

ON

2

ON

3

OFF

4

OFF

5

OFF

6

OFF

7

OFF

8

n/a

In this mode:

  • JTAG functionality is not available

  • Vol- touch button is not available for use with the API

  • AUX Input detection from the API is not available

JTAG

Provides access to the JTAG interface of ESP32-WROVER-E Module. It may be used for debugging, application upload, as well as implementing several other functions.

Enable JTAG

Set Function DIP Switch to:

DIP SW

Position

1

OFF

2

OFF

3

ON

4

ON

5

ON

6

ON

7

ON

8

n/a

In this mode:

  • MicroSD Card functionality is not available, remove the card from the slot

  • Vol- touch button is not available for use with the API

  • AUX Input detection from the API is not available

Battery

The board has a constant current & constant voltage linear charger for single cell lithium-ion batteries AP5056. Used for charging of a battery connected to the Battery Socket over the Micro USB Port.

Note

Please verify if polarity on the battery plug matches polarity of the socket as marked on the board’s soldermask besides the socket.

Note

The Power On Switch does not affect/disconnect the Li-ion battery charging.

Pin Mapping

Several pins ESP32 module are allocated to the on board hardware. Some of them, like GPIO0 or GPIO2, have multiple functions. Please refer to the table below.

GPIO Pin

Type

Function Definition

SENSOR_VP

I

Audio Rec (PB)

SENSOR_VN

I

Audio Mode (PB)

IO32

I/O

Audio Set (TP)

IO33

I/O

Audio Play (TP)

IO27

I/O

Audio Vol+ (TP)

IO13

I/O

JTAG MTCK, MicroSD D3, Audio Vol- (TP)

IO14

I/O

JTAG MTMS, MicroSD CLK

IO12

I/O

JTAG MTDI, MicroSD D2, Aux signal detect

IO15

I/O

JTAG MTDO, MicroSD CMD

IO2

I/O

Automatic Upload, MicroSD D0

IO4

I/O

MicroSD D1

IO34

I

MicroSD insert detect

IO0

I/O

Automatic Upload, I2S MCLK

IO5

I/O

I2S SCLK

IO25

I/O

I2S LRCK

IO26

I/O

I2S DSDIN

IO35

I

I2S ASDOUT

IO19

I/O

Headphone jack insert detect

IO22

I/O

Green LED indicator

IO21

I/O

PA Enable output

IO18

I/O

I2C SDA

IO23

I/O

I2C SCL

  • (TP) - touch pad

  • (PB) - push button

There are several pin headers available to connect external components, check the state of particular signal bus or debug operation of ESP32. Note that some signals are shared.

UART Header / JP2

Header Pin

1

3.3V

2

TX

3

RX

4

GND

I2S Header / JP4

I2C Header Pin

ESP32 Pin

1

MCLK

GPIO0

2

SCLK

GPIO5

1

LRCK

GPIO25

2

DSDIN

GPIO26

3

ASDOUT

GPIO35

3

GND

GND

I2C Header / JP5

I2C Header Pin

ESP32 Pin

1

SCL

GPIO23

2

SDA

GPIO18

3

GND

GND

JTAG Header / JP7

ESP32 Pin

JTAG Signal

1

MTDO / GPIO15

TDO

2

MTCK / GPIO13

TCK

3

MTDI / GPIO12

TDI

4

MTMS / GPIO14

TMS

Note

JTAG cannot be used if MicroSD Card is enabled.

Configurations

audio

This configuration uses the I2S0 peripheral and the ES8388 audio codec present on the LyraT board to play an audio file streamed over HTTP while connected to a Wi-Fi network.

Simple HTTP server

Prepare a PCM-encoded (.wav) audio file with 16 bits/sample (sampled at 44.1kHz). This file must be placed into a folder in a computer that could be accessed on the same Wi-Fi network the ESP32 will be connecting to.

Python provides a simple HTTP server. cd to the audio file folder on the PC and run:

$ python3 -m http.server

Serving HTTP on 0.0.0.0 port 8000 (http://0.0.0.0:8000/)

Look for your PC IP address and test playing the prepared audio on your browser:

../../../../../_images/esp32-lyrat-v4.3-audio-config-file.png

After successfully built and flashed, connect the board to the Wi-Fi network:

$ nsh> wapi psk wlan0 mypasswd 1
$ nsh> wapi essid wlan0 myssid 1
$ nsh> renew wlan0

Once connected, open NuttX’s player and play the file according to its file name and the IP address of the HTTP server (For example tones.wav and 192.168.1.239:8000, respectively):

$ nsh> nxplayer
$ nxplayer> play http://192.168.1.239:8000/tones.wav

Note

The codec implementation on the LyraT board was validated using 16-bit, 44.1kHz WAV files. Other configurations might not work as expected.

nsh

Basic NuttShell configuration (console enabled in UART0, exposed via USB connection by means of the CP2102N bridge, at 115200 bps).

wapi

Enables Wi-Fi support.