Waveshare RP2040 LCD 1.28

The Waveshare RP2040 LCD 1.28 is a low-cost, high-performance MCU board designed by Waveshare based on RP2040 with onboard 1.28 inch LCD.

../../../../../_images/RP2040-LCD-1.28.jpg

Features

  • RP2040 MCU chip designed by Raspberry Pi in the United Kingdom

  • Dual-core Arm Cortex M0+ processor, flexible clock running up to 133 MHz

  • 264KB of SRAM, and 2MB of onboard Flash memory

  • Type-C connector, keeps it up to date, easier to use

  • Onboard 1.28-inch 240 x 240 resolution, 65K RGB IPS LCD display for clear color pictures

  • Lithium battery recharge/discharge header, suitable for mobile devices

  • All GPIOs are adapted through 1.27 pitch female headers (There are 30 pins in total, but some pins have been connected to the internal circuit, you need to pay attention when multiplexing, please refer to the wiki for details)

  • USB 1.1 with device and host support

  • Low-power sleep and dormant modes

  • Drag-and-drop programming using mass storage over USB

  • 2 x SPI, 2 x I2C, 2 x UART, 2 x UART, 4 x 12-bit ADC, 16 x controllable PWM channels

  • Accurate clock and timer on-chip

  • Temperature sensor

  • Accelerated floating-point libraries on-chip

  • 8 x Programmable I/O (PIO) state machines for custom peripheral support

Serial Console

By default a serial console appears on pins 1 (TX GPIO0) and pin 2 (RX GPIO1). This console runs a 115200-8N1.

The board can be configured to use the USB connection as the serial console.

Buttons and LEDs

No user LED is provided.

A BOOT button, which if held down when pressing RESET or power is first applied to the board, will cause the RP2040 to boot into programming mode and appear as a storage device to a computer connected via USB. Saving a .UF2 file to this device will replace the Flash ROM contents on the RP2040.

Pin Mapping

Pad

Signal

Notes

2

GPIO0

Default TX for UART0 serial console

4

GPIO1

Default RX for UART0 serial console

Power Supply

The Raspberry Pi Pico can be powered via the USB connector, connecting a lithium battery through connector, or by supplying +5V to pin 18(VSYS). The board had a diode that prevents power from pin 18 from flowing back to the USB socket. Power through USB or VSYS will be charging the battery if connected. The schematic is available at RP2040-LCD-1.28-sch.pdf

Configurations

composite

NuttShell configuration (console enabled in UART0, at 115200 bps) with support for CDC/ACM with MSC USB composite driver.

nsh

Basic NuttShell configuration (console enabled in UART0, at 115200 bps).

nsh-flash

Basic NuttShell configuration (console enabled in UART0, at 115200 bps with SMART flash filesystem.

nshsram

NuttShell configuration (console enabled in UART0, at 115200 bps) with interrupt vectors in RAM.

smp

Basic NuttShell configuration (console enabled in UART0, at 115200 bps) with both ARM cores enabled.

spisd

NuttShell configuration (console enabled in UART0, at 115200 bps) with SPI configured.

usbmsc

NuttShell configuration (console enabled in UART0, at 115200 bps) with support for usbmsc.

usbnsh

Basic NuttShell configuration (console enabled in USB Port, at 115200 bps).

fb

NuttShell configuration (console enabled in USB Port, at 115200 bps) with support for gc9a01 and video framebuffer example.

lvgl

NuttShell configuration (console enabled in USB Port, at 115200 bps) with support for gc9a01 and LVGL demo (using lcd_dev).