Debugging

Finding and fixing bugs is an important part of the hardware and software development process. Sometimes you also need to use debugging techniques to understand how the system works. Two tools that are helpful are debug logging and debugging using the GNU Debugger (gdb).

Debug Logging

NuttX has a powerful system logging facility (syslog) with info, warn, and error levels. You can enable debugging for your build for the subsystem or feature by using the menuconfig system.

The debug options are available under Build Setup ‣ Debug Options. You will most likely have to enable the following options:

  • Enable Debug Features — selecting this will turn on subsystem-level debugging options, they will become visible on the page below. You can then select the ones you want.

  • Enable Error Output — this will only log errors.

  • Enable Warnings Output — this will log warnings and errors.

  • Enable Informational Debug Output — this will produce informational output, warnings, and errors.

You can then select from the subsystems that are available, Network, Scheduler, USB, etc. Note that you will need to separately enable the subsystem elsewhere in the menuconfig system. To see the CONFIG define that is set, use the arrow keys to highlight the subsystem (for instance, Network Debug Features) and type ?. This will show you that the C macro that is set is called CONFIG_DEBUG_NET. debug.h defines the netinfo() logging function that will log output if this macro is set. You can search the source code for netinfo to see how it is used.

Screenshot of menuconfig system main screen

Note that enabling all these will produce an incredible amount of logging output. Enable the level you want and the area you’re interested in, and leave the rest disabled, save the config, and then recompile. You can see the full list of debug feature logging functions in the file debug.h.

Syslog timestamps can be enabled in the configuration in Device Drivers ‣ System Logging ‣ Prepend timestamp to syslog message (CONFIG_SYSLOG_TIMESTAMP).

You may need to do a little bit of experimenting to find the combination of logging settings that work for the problem you’re trying to solve. See the file debug.h for available debug settings that are available.

There are also subsystems that enable USB trace debugging, and you can log to memory too, if you need the logging to be faster than what the console can output.

Debugging with openocd and gdb

To debug our Nucleo board using its embedded SWD debug adapter, start openocd with the following command:

$ openocd -f interface/stlink-v2.cfg -f target/stm32f1x.cfg

This will start a gdb server. Then, start gdb with:

$ cd nuttx/
$ gdb-multiarch nuttx/nuttx

Inside gdb console, connect to the gdb server with:

(gdb) target extended-remote :3333

You can now use standard gdb commands. For example, to reset the board:

(gdb) mon reset

To halt the board:

(gdb) mon halt

To set a breakpoint:

(gdb) breakpoint nsh_main

and to finally start nuttx:

(gdb) continue
Continuing.

Breakpoint 1, nsh_main (argc=1, argv=0x200ddfac) at nsh_main.c:208
208     sched_getparam(0, &param);
(gdb) continue
Continuing.

Tip

You can abbreviate gdb commands: info b is a shortcut for information breakpoints; c works the same as continue, etc.

NuttX aware debugging

Since NuttX is actually an RTOS, it is useful to have gdb be aware of the different tasks/threads that are running. There are two ways to do this: via openocd itself or via gdb. Note that in both cases, you need to enable debug symbols (CONFIG_DEBUG_SYMBOLS).

With openocd

openocd supports various RTOS directly, including NuttX. It works by reading into internal NuttX symbols which define the active tasks and their properties. As a result, the gdb server will directly be aware of each task as a different thread. The downside of this approach is that it depends on how you build NuttX as there are some options hardcoded into opencd. By default, it assumes:

  • CONFIG_DISABLE_MQUEUE=y

  • CONFIG_PAGING=n

If you need these options to be set differently, you will have to edit ./src/rtos/nuttx_header.h from openocd, change the corresponding settings and then rebuild it.

Finally, to enable NuttX integration, you need to supply an additional openocd argument:

$ openocd -f interface/stlink-v2.cfg -f target/stm32f1x.cfg -c '$_TARGETNAME configure -rtos nuttx'

Since openocd also needs to know the memory layout of certain datastructures, you need to have gdb run the following commands once the nuttx binary is loaded:

eval "monitor nuttx.pid_offset %d", &((struct tcb_s *)(0))->pid
eval "monitor nuttx.xcpreg_offset %d", &((struct tcb_s *)(0))->xcp.regs
eval "monitor nuttx.state_offset %d", &((struct tcb_s *)(0))->task_state
eval "monitor nuttx.name_offset %d", &((struct tcb_s *)(0))->name
eval "monitor nuttx.name_size %d", sizeof(((struct tcb_s *)(0))->name)

One way to do this is to define a gdb hook function that will be called when running file command:

define hookpost-file
  eval "monitor nuttx.pid_offset %d", &((struct tcb_s *)(0))->pid
  eval "monitor nuttx.xcpreg_offset %d", &((struct tcb_s *)(0))->xcp.regs
  eval "monitor nuttx.state_offset %d", &((struct tcb_s *)(0))->task_state
  eval "monitor nuttx.name_offset %d", &((struct tcb_s *)(0))->name
  eval "monitor nuttx.name_size %d", sizeof(((struct tcb_s *)(0))->name)
end

You will see that openocd has received the memory offsets in its output:

Open On-Chip Debugger 0.10.0+dev-01514-ga8edbd020-dirty (2020-11-20-14:23)
Licensed under GNU GPL v2
For bug reports, read
        http://openocd.org/doc/doxygen/bugs.html
Info : auto-selecting first available session transport "swd". To override use 'transport select <transport>'.
Info : target type name = cortex_m
Info : Listening on port 6666 for tcl connections
Info : Listening on port 4444 for telnet connections
15:41:23: Debugging starts
Info : CMSIS-DAP: SWD  Supported
Info : CMSIS-DAP: FW Version = 1.10
Info : CMSIS-DAP: Interface Initialised (SWD)
Info : SWCLK/TCK = 1 SWDIO/TMS = 1 TDI = 0 TDO = 0 nTRST = 0 nRESET = 1
Info : CMSIS-DAP: Interface ready
Info : clock speed 1000 kHz
Info : SWD DPIDR 0x2ba01477
Info : nrf52.cpu: hardware has 6 breakpoints, 4 watchpoints
Info : starting gdb server for nrf52.cpu on 3333
Info : Listening on port 3333 for gdb connections
Info : accepting 'gdb' connection on tcp/3333
Error: No symbols for NuttX
Info : nRF52832-QFAA(build code: B0) 512kB Flash, 64kB RAM
undefined debug reason 8 - target needs reset
Warn : Prefer GDB command "target extended-remote 3333" instead of "target remote 3333"
Info : pid_offset: 12
Info : xcpreg_offset: 132
Info : state_offset: 26
Info : name_offset: 208
Info : name_size: 32
target halted due to debug-request, current mode: Thread
xPSR: 0x01000000 pc: 0x000000dc msp: 0x20000cf0
target halted due to debug-request, current mode: Thread xPSR: 0x01000000 pc: 0x000000dc msp: 0x20000cf0

Note

You will probably see the Error: No symbols for NuttX error appear once at startup. This is OK unless you see it every time you step the debugger. In this case, it would mean you did not enable debug symbols.

Now, You can now inspect threads:

(gdb) info threads
  Id   Target Id         Frame
* 1    Remote target     nx_start_application () at init/nx_bringup.c:261
(gdb) info registers
r0             0x0                 0
r1             0x2f                47
r2             0x0                 0
r3             0x0                 0
r4             0x0                 0
r5             0x0                 0
r6             0x0                 0
r7             0x20000ca0          536874144
r8             0x0                 0
r9             0x0                 0
r10            0x0                 0
r11            0x0                 0
r12            0x9                 9
sp             0x20000c98          0x20000c98
lr             0x19c5              6597
pc             0x1996              0x1996 <nx_start_application+10>
xPSR           0x41000000          1090519040
fpscr          0x0                 0
msp            0x20000c98          0x20000c98
psp            0x0                 0x0 <_vectors>
primask        0x0                 0
basepri        0xe0                -32
faultmask      0x0                 0
control        0x0                 0

With gdb

You can also do NuttX aware debugging using gdb scripting support. The benefit is that it works also for the sim build where openocd is not applicable. For this to work, you will need to enable PROC filesystem support which will expose required task information (CONFIG_FS_PROCFS=y).

To use this approach, you can load the nuttx/tools/nuttx-gdbinit file. An easy way to do this is to create a symbolic link:

$ cd $HOME
$ ln -s nuttx/tools/nuttx-gdbinit .gdbinit

This way whenever gdb is started it will run the appropriate commands. To inspect the threads you can now use the following gdb command:

(gdb) info_nxthreads
target examined
_target_arch.name=armv7e-m
$_target_has_fpu : 0
$_target_has_smp : 0
saved current_tcb (pid=0)
* 0 Thread 0x20000308  (Name: Idle Task, State: Running, Priority: 0) 0xdc in __start()
  1 Thread 0x20001480  (Name: init, State: Waiting,Semaphore, Priority: 100) 0x7e08 in arm_switchcontext()