======================== Adafruit KB2040 Kee Boar ======================== .. tags:: chip:rp2040 The KB2040 Kee Boar is a general purpose RP2040 board supplied by Adafruit. .. figure:: KB2040.png :align: center See the `Adafruit website `_ for information about Adafruit KB2040. Features ======== * RP2040 microcontroller chip * Dual-core ARM Cortex M0+ processor, flexible clock running up to 133 MHz * 264kB of SRAM, and 8MB of on-board Flash memory * Castellated module allows soldering direct to carrier boards * USB Host and Device support via type C connector. * Low-power sleep and dormant modes * Drag & drop programming using mass storage over USB * 18 multi-function GPIO pins * 2× SPI, 2× I2C, 2× UART, 3× 12-bit ADC, 16× controllable PWM channels * Accurate clock and timer on-chip * Temperature sensor * Accelerated floating point libraries on-chip * 8 × Programmable IO (PIO) state machines for custom peripheral support * On-board STEMMA QT connector for quick I2C connection. Buttons and LEDs ================ There is a BOOT button which if held down when power is first applied or the RESET button is pressed will cause the RP2040 to boot into program mode and appear as a storage device to a USB connector. Saving a .UF2 file to this device will replace the Flash ROM contents on the RP2040. A RESET button that allows rebooting the board without disconnecting the power. A ws2812 (NeoPixel) smart RGB LED controlled by GPIO17. Pin Mapping =========== Pads numbered anticlockwise from USB connector. ===== ========== ========== Pad Signal Notes ===== ========== ========== 1 D+ Alternate USB data connection. 2 GPIO0 Default TX for UART0 serial console 3 GPIO1 Default RX for UART0 serial console 4 Ground 5 Ground 6 GPIO2 7 GPIO3 8 GPIO4 9 GPIO5 10 GPIO6 11 GPIO7 12 GPIO8 13 GPIO9 14 GPIO10 15 GPIO19 16 GPIO20 17 GPIO18 18 GPIO26 ADC0 19 GPIO27 ADC1 20 GPIO28 ADC2 21 GPIO29 ADC3 22 Ground 23 Raw Connected to USB +5V line 24 D- Alternate USB data connection. ===== ========== ========== The board has a STEMMA QT connector that is also connected to pins GPI12 (I2C1 SDA) and GPI13 (I2C1 SDA). Power Supply ============ The Raspberry Pi Pico can be powered via the USB connector, or by supplying +5V to pin 23. The Raspberry Pi Pico chip run on 3.3 volts. This is supplied by an onboard voltage regulator. Installation & Build ==================== For instructions on how to to install the build dependencies and create a NuttX image for this board, consult the main :doc:`RP2040 documentation <../../index>`. Configurations ============== All configurations listed below can be configured using the following command in the ``nuttx`` directory (again, consult the main :doc:`RP2040 documentation <../../index>`): .. code:: console $ ./tools/configure.sh adafruit-kb2040: audiopack --------- NuttShell configuration (console enabled in UART0, at 115200 bps) with support for NXPlayer audio player. Pico Audio Pack support. See the following page for connection: https://shop.pimoroni.com/products/pico-audio-pack SD card interface is also enabled. composite --------- NuttShell configuration (console enabled in UART0, at 115200 bps) with support for CDC/ACM with MSC USB composite driver. ``conn`` command enables the composite device. displaypack ----------- NuttShell configuration (console enabled in USB Port, at 115200 bps) supporting ST7789 video display. See the following page for connection: https://shop.pimoroni.com/products/pico-display-pack enc28j60 -------- NuttShell configuration (console enabled in UART0, at 115200 bps) with support for ENC28J60. ENC28J60 SPI ethernet controller supports: - IP address is configured by DHCP. - DNS address is 8.8.8.8 (CONFIG_NETINIT_DNSIPADDR) - NTP client is enabled. .. list-table:: ENC28J60 connections :widths: auto :header-rows: 1 * - ENC28J60 - Raspberry Pi Pico W * - GND - GND (Pin 3 or 38 or ...) * - 3.3V - 3V3 OUT (Pin 36) * - SI - GP15 (SPI1 TX) (Pin 20) * - SCK - GP14 (SPI1 SCK) (Pin 19) * - CS - GP13 (SPI1 CSn) (Pin 17) * - SO - GP12 (SPI1 RX) (Pin 16) * - INT - GP11 (Pin 15) * - RESET - GP10 (Pin 14) lcd1602 ------- NuttShell configuration (console enabled in UART0, at 115200 bps) with support for LCD1602 Segment LCD Display (I2C). .. list-table:: LCD1602 connections :widths: auto :header-rows: 1 * - PCF8574 BackPack - Raspberry Pi Pico W * - GND - GND (Pin 3 or 38 or ...) * - VCC - 5V Vbus (Pin 40) * - SDA - GP4 (I2C0 SDA) (Pin 6) * - SCL - GP5 (I2C0 SCL) (Pin 7) nsh --- Basic NuttShell configuration (console enabled in UART0, at 115200 bps). nsh-flash --------- Basic NuttShell configuration (console enabled in UART0, at 115200 bps with SMART flash filesystem. nshsram ------- NuttShell configuration (console enabled in UART0, at 115200 bps) with interrupt vectors in RAM. smp --- Basic NuttShell configuration (console enabled in UART0, at 115200 bps) with both ARM cores enabled. spisd ----- NuttShell configuration (console enabled in UART0, at 115200 bps) with SPI SD card support enabled. .. list-table:: spisd connections :widths: auto :header-rows: 1 * - SD card slot - Raspberry Pi Pico W * - DAT2 - Not connected * - DAT3/CS - GP17 (SPI0 CSn) (Pin 22) * - CMD /DI - GP19 (SPI0 TX) (Pin 25) * - VDD - 3V3 OUT (Pin 36) * - CLK/SCK - GP18 (SPI0 SCK) (Pin 24) * - VSS - GND (Pin 3 or 38 or ...) * - DAT0/DO - GP16 (SPI0 RX) (Pin 21) * - DAT1 - Not connected Card hot swapping is not supported. ssd1306 ------- NuttShell configuration (console enabled in UART0, at 115200 bps) with support for SSD1306 OLED display (I2C) test configuration. .. list-table:: SSD1306 connections :widths: auto :header-rows: 1 * - SSD1306 - Raspberry Pi Pico W * - GND - GND (Pin 3 or 38 or ...) * - VCC - 3V3 OUT (Pin 36) * - SDA - GP4 (I2C0 SDA) (Pin 6) * - SCL - GP5 (I2C0 SCL) (Pin 7) st7735 ------ NuttShell configuration (console enabled in UART0, at 115200 bps) with support for ST7735 SPI LCD. .. list-table:: ST7735 connections :widths: auto :header-rows: 1 * - st7735 - Raspberry Pi Pico W * - GND - GND (Pin 3 or 38 or ...) * - VCC - 5V Vbus (Pin 40) * - SDA - GP15 (SPI1 TX) (Pin 20) * - SCK - GP14 (SPI1 SCK) (Pin 19) * - CS - GP13 (SPI1 CSn) (Pin 17) * - AO(D/C) - GP12 (SPI1 RX) (Pin 16) * - BL - GP11 (Pin 15) * - RESET - GP10 (Pin 14) usbmsc ------ NuttShell configuration (console enabled in UART0, at 115200 bps) with support for USB MSC and CDC/ACM. ``msconn`` and ``sercon`` commands enable the MSC and CDC/ACM devices. The MSC support provides the interface to the SD card with SPI, so the SD card slot connection like spisd configuration is required. usbnsh ------ Basic NuttShell configuration using CDC/ACM serial (console enabled in USB Port, at 115200 bps). waveshare-lcd-1.14 ------------------ NuttShell configuration (console enabled in UART0, at 115200 bps) with support for st7789. waveshare-lcd-1.3 ----------------- NuttShell configuration (console enabled in UART0, at 115200 bps) with support for usbmsc.